# How Much Do Soffit and Fascia Cost in Toronto? (2026 Prices per Foot and per Home)

> Replacing soffit and fascia with vented aluminum costs $12–$24 per linear foot installed in Toronto and the GTA in 2026 — roughly $3,500–$9,000 for a typical detached home with 200–350 ft of roof edge. Fascia alone runs $7–$12 per foot and soffit alone $6–$14 depending on the overhang width. Seamless aluminum eavestroughs add $8–$15 per foot, so a full edge package — soffit, fascia and eavestroughs — lands at $5,000–$13,000 for most houses, and 15–25% less when done with a new roof.

*Category: roofing | 6 min read | Updated 2026-10-01*

## What soffit and fascia do

Fascia is the vertical board at the edge of the roof that the eavestroughs hang from. Soffit is the horizontal panel underneath the overhang that closes the eave and — if it is vented — lets outdoor air into the attic. Together they keep water, squirrels and birds out of the roof structure and, on a properly ventilated house, they are half of the system that stops ice dams. Most Toronto houses still have original wood fascia under a thin aluminum cap and either solid plywood soffit or perforated aluminum installed decades ago, which is why rot at the fascia and blocked intake vents are the two most common findings on a roof inspection.

## 2026 price guide

| Scope | Installed cost per linear ft | Typical detached home (200–350 ft) |
| --- | --- | --- |
| Fascia only (aluminum over existing board) | $7–$12 | $1,500–$4,000 |
| Soffit only (vented aluminum, 12–24 in overhang) | $6–$14 | $1,500–$4,500 |
| Soffit + fascia | $12–$24 | $3,500–$9,000 |
| Seamless aluminum eavestroughs | $8–$15 | $1,500–$4,000 |
| Soffit + fascia + eavestroughs | $20–$39 | $5,000–$13,000 |
| Replace rotted wood fascia board | +$6–$12 per ft affected | Typically $300–$1,500 |

Prices include removing the old material, new vented aluminum soffit and J-channel, aluminum fascia cap, drip edge where the roof needs it and disposal. They assume a one- or two-storey house with ordinary access. Three-storey homes, steep lots and houses that need scaffolding rather than ladders sit at the top of each range.

## What moves the price

1. Overhang width. A 12-inch soffit uses half the material of a 24-inch one and installs faster.
2. Rot. Fascia board that has rotted behind the old cap has to be replaced before anything goes on; budget $6–$12 per affected foot.
3. Height and access. Second- and third-storey eaves over a sloped side yard mean scaffolding or a lift.
4. Gable ends and returns. Every corner, return and gable rake adds cut-and-fit time compared with a straight run.
5. Colour and gauge. Standard white or brown stock is cheapest; custom colours and heavier-gauge fascia cost more.
6. Bundling. With eavestroughs, a roof or attic ventilation, the set-up cost is shared and the price per foot falls 15–25%.

## Why 'vented' matters more than 'cheap'

Intake ventilation through the soffit, paired with exhaust at the ridge, is how an attic stays cold in winter. A cold attic does not melt the snow above it, so meltwater does not refreeze at the eave into an ice dam. Solid soffit, soffit installed over old plywood with no cut-outs, or vents stuffed with insulation from inside the attic all defeat that. When we replace soffit we confirm the intake path is actually open from the attic side — it is the single most common thing a 'cheap' soffit job skips, and the reason ice dams come back the following winter.

> If your roof is within five years of replacement, do the soffit and fascia with the roof. The crew, the scaffolding and the drip-edge detailing are shared, and a roof warranty that covers the edge is worth more than two separate ones that each blame the other.

**Q: Can I just cap the old fascia instead of replacing it?**

Only if the wood behind it is sound. Capping over rot hides it for a few years while the eavestrough hangers lose their grip. We probe the board along the full run and replace the sections that fail before capping; it usually adds a few hundred dollars, not thousands.

**Q: How long does aluminum soffit and fascia last?**

30–40 years. The aluminum itself does not rot or rust; what ends its life is the paint finish fading or the fasteners working loose, both of which are repairable. It will typically outlast one full asphalt roof and most of a second.

**Q: Do I need a permit for soffit and fascia in Toronto?**

No. Replacing soffit, fascia and eavestroughs is maintenance and does not require a building permit in Toronto or the surrounding municipalities, unless the work is part of a larger permitted roof or addition project.

**Q: What is the cheapest way to do soffit and fascia?**

Bundle it with eavestroughs or a roof replacement and choose standard stock colours. Doing fascia alone and leaving solid soffit in place is cheaper on the invoice but leaves the attic without intake air, which costs more in ice-dam damage than it saves.

## Related Services
- [Eavestrough, Soffit & Fascia](https://buildoreno.ca/eavestrough-gutters)
- [Attic Ventilation & Insulation](https://buildoreno.ca/attic-ventilation)
- [Roof Repair](https://buildoreno.ca/roof-repair)
- [Metal Roofing](https://buildoreno.ca/metal-roofing)

[Read full article](https://buildoreno.ca/blog/soffit-fascia-cost-toronto)